Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Everett Homeowners Choose Gelco Chimney Cleaning
We provide independent Gelco chimney cleaning, inspection, and repair service in Everett, WA. Our technicians know Gelco liner systems by their fittings, insulation requirements, and appliance connections, so we can diagnose a venting fault without guessing. We are not affiliated with, authorized by, or endorsed by Gelco; we’re an independent chimney specialist that works with Gelco components the way the trade actually uses them.
That distinction matters in Everett. This is one of the wettest marine climates in the country, and a liner that vents beautifully in a dry inland town will show water intrusion and corrosion here if its tee gaskets, cap, and appliance adapter aren’t handled correctly. We sweep, we inspect at Level 2, and we repair with professional-grade parts that fit the system that’s already in your chimney. One team handles the whole job. Call (888) 545-1163. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Chimney Sweep Everett for Your Gelco Chimney Cleaning?
Our technicians have up to 15 years of experience, and a good share of that time has been spent with stainless liner systems like the ones Gelco builds. That hands-on familiarity is what lets us look at a Flex King Pro installation and tell you whether the joint clamps are the originals, whether the tee snout was pitched for drainage, and whether the appliance adapter was sealed properly at the collar. You can’t learn that from a manufacturer’s spec page.
We use Gelco OEM components for liner connections, tees, and caps so fit and corrosion resistance stay where they should, and we use quality stainless aftermarket fasteners where OEM isn’t available. Nothing about that voids your warranty; sloppy work does. We don’t stock, carry, or sell genuine Gelco parts, and we aren’t a dealer, so our interest in your repair is honest. Our focus covers DuraFlex and HeatShield systems as well, so if your home has more than one chimney setup, we’re not learning on your dime.
Warranty-safe practice boils down to a few habits: match the component to the liner, don’t over-torque joint fasteners, keep the appliance connection sealed, and test the draft before calling a job done. We do all four, every time.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common Gelco Chimney Cleaning Problems We Fix in Everett
These are the failure patterns we see most often when we’re called out to a Gelco installation in Everett. None of them are rare. Most are the product of damp Northwest weather meeting a small installation detail that was never quite right.
- Corrosion at the appliance collar. Condensate pools inside Gelco flex liners when the appliance adapter isn’t sealed or pitched correctly, and it sits right at the collar. Rust at that joint is the first sign, and it usually shows up as a chalky orange stain at the flue pipe connection rather than at the top of the chimney. Left alone, the pool eats the adapter and starts working on the liner itself.
- Tee snout and cap gasket degradation. Exterior Gelco tees take a beating in Everett’s rain, and the snout and cap gaskets are the parts that fail first. When they do, water tracks down the outside of the liner and leaves rust streaks across the chimney face and staining in the firebox. Owners often assume the masonry is the problem. It’s usually the gasket.
- Liner separation and fastener back-out. Older Gelco installations sometimes used non-stainless clamps at the joints, and those corrode through in wet conditions. Over-torqued clamps cause a different problem: the fastener backs out and the joint opens. Either way, you get reduced draft, smoke spilling at the appliance, and a joint that needs attention before the next burn season.
- Oversized liner with weak draft. A Gelco liner that wasn’t sized to the appliance’s flue collar will underperform, and the symptom is creosote. Weak draft means a slower, cooler flue, which means more deposits on the liner wall. This turns up often after a stove swap, when the new appliance doesn’t match the liner the previous owner installed.
- Damp creosote glaze in older brick flues. Everett’s wet winter air keeps soot from fully drying, and in north-end brick chimneys we routinely find glazed, third-degree creosote that looks nothing like the dry flaky soot technicians see east of the Cascades. That glaze needs proper removal, not a quick brush pass, and it’s the main reason our Level 2 Inspection and Creosote Removal work travels together.
Gelco Parts & Our Repair-vs-Replace Approach
We don’t replace a liner because it’s old. We replace it because the camera shows damage, mis-sizing, or a joint that can’t be made sound again. Otherwise the job is a clean, a re-seal, and re-supporting the components that are already there, and that’s the recommendation you’ll get.
For parts, we use Gelco OEM components for liner connections, tees, and caps, and quality stainless aftermarket fasteners where the OEM piece isn’t obtainable. We don’t claim to stock OEM or genuine Gelco parts. What we do promise is that every part we fit is chosen to match your system rather than to hit a price point. Off-brand collars and mild-steel clamps are the single most common reason a repair fails early in a marine climate.
Repair wins when the liner itself is sound and the problem lives in the tee, cap, gasket, or adapter. Replace wins when the liner is holed, separated at a joint that can’t be re-clamped, or sized wrong for the appliance it serves. If you’re not sure which side of that line you’re on, a Level 2 Inspection with a camera and photo report settles it. Call (888) 545-1163 and we’ll book a sweep and inspection so you can see what we see.
Our Gelco Service Process – Step by Step
- 1
Diagnosis. We start with a Level 2 Inspection, running a camera through the flue and physically inspecting the exterior tee, cap, and appliance connection. On Gelco systems we’re specifically looking at gasket condition, joint fasteners, adapter sealing, and pitch. You get photos of every finding.
- 2
Sweep and creosote removal. We sweep with poly brushes suited to a stainless liner wall, then remove creosote glaze where it’s built up. We confirm the liner stays intact as we go, because a stainless liner swept too aggressively shows wear at the joints.
- 3
Repair or install. Tee gaskets, caps, and adapters get replaced with components that fit. Where a full re-line is the honest call, we install a Gelco liner sized to the appliance’s flue collar, seal the appliance connection, and set the pitch correctly.
- 4
Test. We verify draft, check for leaks at every joint, and confirm the cap is correctly sized and seated. A repair that isn’t tested isn’t finished.
- 5
Documentation and warranty. You get the photo report and a written record of what was replaced and why, which is what a manufacturer wants to see if a component ever requires a warranty conversation.
See the difference
Before
After
Before
After
Before
AfterGelco Products We Service & Install in Everett
We work with the Gelco liner and component line as it’s installed in real homes around Everett: the Gelco Flex King Pro stainless liner, the Gelco Flex King HD liner, the Gelco Forever Flex liner, and Gelco insulated Tee and Cap kits. The two Flex King systems cover the majority of residential wood and gas appliance venting we see, while Forever Flex turns up in longer runs and heavier-use installations.
On the component side, Gelco insulated tee and cap kits are where most of our repair work concentrates, because they’re the parts exposed to weather. Cap replacement, gasket renewal, and tee re-sealing are routine jobs for us, along with full liner installation where a re-line is warranted. We also handle the appliance adapter and connection details that determine whether a liner lasts in this climate.
We Also Service These Brands
Everett homes hold a mix of liner systems, and we work across the major professional brands, not just Gelco. That includes DuraFlex liner systems and HeatShield applications for chimney restoration, plus Olympia Chimney, Famco, and Copperfield components for caps, dampers, and weatherproofing. A homeowner with a Gelco liner and a DuraFlex top plate, or a HeatShield-restored flue feeding a Gelco liner, doesn’t need to call two contractors.
FAQs – Gelco Chimney Cleaning Service in Everett
No. We are an independent chimney service provider with no affiliation, authorization, or endorsement from Gelco. We work on Gelco liners and components using our own trade knowledge and quality parts that fit, and we say so plainly because the distinction tells you something about how we operate. When we recommend a repair, it’s based on what the camera shows, not on a manufacturer relationship.
Yes. A Level 2 Inspection with a camera lets us see the full interior of a Gelco Flex King liner without pulling it, and that’s how we check joint condition, creosote buildup, and any corrosion at the appliance collar. The exterior tee and cap get a physical inspection at the same time, since a camera won’t show you a gasket that’s crumbling. Call (888) 545-1163 to book it.
A leaking Gelco tee almost always means the snout gasket or cap gasket has degraded, letting Everett rain into the tee and down the outside of the liner. The rust streaks you see on the chimney face are the visible half of the problem; the other half is water sitting against the liner and fasteners. The usual fix is to pull and inspect the tee and cap, replace the gaskets and fasteners, and check that the cap is correctly sized and seated. Call (888) 545-1163 for an exact quote; estimates are free.
Yes, a poly brush is the correct tool for a stainless Gelco liner, and it’s what we use. Stiff metal brushes are a bad match for stainless, because they can scuff the wall and stress the joint fasteners. Our technicians sweep with poly and watch the joints as they go, because Everett’s damp creosote often needs more than one pass to clear. Call (888) 545-1163 if you’d rather not find out the hard way what a wrong brush does.
You know by matching the liner’s diameter to the appliance’s flue collar and confirming it with a draft test. An oversized Gelco liner is a common cause of weak draft and heavy creosote after a stove swap, and the appliance will tell on it: smoke spillage on reload, sluggish starts, and soot where you wouldn’t expect it. Our inspection measures and tests rather than eyeballs it. Call (888) 545-1163 for a sweep and inspection so we can confirm the sizing.
You can usually replace just the cap. In most cases the Gelco liner itself is fine and the cap has simply failed or come loose, which is one of the more common calls we get after a windstorm in Everett. A qualified sweep will confirm the liner is sound, then fit a correctly sized cap that seats properly on the liner top. A new liner only enters the conversation if the camera shows damage or mis-sizing. Call (888) 545-1163 for an exact quote; estimates are free.
A Gelco chimney sweep in Everett typically runs in the low-to-mid hundreds, with a Level 2 Inspection with camera and photo report often bundled alongside it and component repairs quoted separately once we know what’s failed. We set the price per job with a written estimate, agreed before we book, and the estimate is free. Call (888) 545-1163 for an exact quote; estimates are free.
Book Your Gelco Service in Everett, WA
Whether you’re chasing a rust streak from a failing tee, hearing a loose cap rattle in the wind, or simply due for a sweep and a proper look at your flue, we can help. We’ll show you what the camera finds and tell you honestly when work can wait. Call (888) 545-1163. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Everett.