Chimney Repair in Everett, WA | Chimney Sweep Everett

Chimney Repair in Everett - You See the Footage Before You Get a Price

Liner and masonry work is where this trade gets a bad name, so nothing is quoted until you have seen the camera footage yourself. Then a written, itemized price with no scope creep.

Call to schedule your free estimate

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Sweep & inspectionSweep & inspection
Caps & crownsCaps & crowns
Flue reliningFlue relining
Masonry repairMasonry repair
Gas fireplace serviceGas fireplace service
Every visit starts with

Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed

Worth knowing

Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.

Get your free estimate

Trusted Chimney Repair for Everett Homeowners

Chimney damage rarely shows itself from the living room. A cracked crown, a pulled flashing flange, or a liner that has spalled out behind the clay tells you nothing until water stains the ceiling or a smoke test fails. That’s the problem chimney repair in Everett actually solves: finding the failure the eye can’t see and fixing the cause, not the symptom.

Worker cutting damaged concrete chimney crown with angle grinder for repair in Everett, WA

Call (888) 545-1163

Our technicians have up to 15 years of experience across sweeping, inspection, and structural repair, and they’re the same people who diagnose the job and write it up. Repairs use professional-grade materials from Olympia Chimney and Famco, so what goes back into the chase is rated for the work it has to do. When a problem turns out to be structural rather than cosmetic, we carry chimney repair through to a HeatShield application or a full reline rather than handing you off. We answer 24/7 at (888) 545-1163, with fast dispatch from 7am to 7pm, Sunday through Friday. Same-day repair is often possible when you call early.

Chimney Cap Installation

Chimney Cap Installation is the fitting of a manufactured cap over the flue opening to keep rain, birds, and debris out of the chimney while still letting exhaust escape. If your flue is bare, the cap is the cheapest protection you’ll ever put on the system. Everett’s wet winter and the leaf drop from the maples and firs around town both find an open flue eventually, and a wet flue is a masonry problem waiting to happen. We install stainless caps sized to the actual flue opening rather than a generic box, often alongside a Chimney Sweep Everett visit. Typical cap installation runs $150 to $400 depending on flue count and cap style.

Sizing the Cap to the Flue

An oversized cap sits loose and rattles free in wind; an undersized one chokes draft. We measure the flue tile itself, not the brick surround, and match the mesh to the appliance. That matters most on open wood-burning fireplaces where draft is already marginal.

Multi-Flue and Custom Caps

Chimneys with two or three flues, or an offset crown, need a custom footprint rather than a stock lid. We fit those in stainless with a removable top so sweeping access stays simple. The cap should never be something you have to fight later.

Explore

Styles & brands we work with

  • Sweep & inspection
  • Caps & crowns
  • Flue relining
  • Masonry repair
  • Gas fireplace service

Chimney Cap Replacement

Chimney Cap Replacement is the removal and refitting of a cap that has rusted through, lost its mesh, or been bent off by wind or a fallen branch. A single storm can flatten the screen on a light-gauge cap; after that, animals and rain walk straight in. We check the cap every time we’re on the roof for a sweep or an inspection, because a cap that looks fine from the ground is often rusted solid at the base. We replace in stainless from Olympia Chimney and Famco, and we tell you plainly when a cap can wait a season. Typical replacement runs $150 to $350 installed, with custom multi-flue caps priced higher.

When Rust or Storm Damage Means Replacement

Surface rust you can brush off is cosmetic. Flaking metal, a mesh that crumbles at the touch, or a tie-down that has let go is not, and a loose cap can slide off the crown in a sneaker wind. We replace those rather than patch them.

Why Cheap Caps Fail Fast

Galvanized caps with thin mesh are the ones that fail in a few seasons around Puget Sound. Stainless holds up. We’d rather quote you a cap that lasts than come back to sell you another one.

Chimney Liner Installation

Chimney Liner Installation is the fitting of a continuous stainless flue liner inside the existing chimney to contain flue gases and carry them safely to the top. It’s the right answer when the original clay tile is cracked, spalling, or missing in sections, or when a new appliance needs an appropriately sized flue. A failed liner is what lets heat reach framing and what sends carbon monoxide into the house instead of up the chimney. We install DuraFlex liner systems sized to the appliance, and we don’t sell a liner you don’t need; the camera footage either shows a problem or it doesn’t. Typical relining runs $2,500 to $6,000, depending on height, flue size, and whether an insulation wrap is required.

Questions about your chimney cleaning?Free estimate, price agreed before work starts
Call (888) 545-1163

Clay Tile Versus Stainless

Original clay tile is only as good as its mortar joints, and those joints crack with heat cycling and settle over time. A stainless liner gives you a continuous, sealed flue that doesn’t depend on a hundred separate joints staying tight.

Backdraft and Draft Problems

A liner that’s too large for the appliance runs cold and smokes. We size by appliance output and flue height, which is where a lot of off-the-shelf fixes go wrong. Getting this right is the whole point of the job.

Chimney Flashing Repair

Chimney Flashing Repair is the correction of the metal flashing and counter-flashing where the chimney meets the roof, the joint that fails more often than any other part of the assembly. Flashing leaks show up as damp patches on the ceiling near the chimney or as rusty staining on the chase, usually first noticed after a stretch of Everett’s fall rain. We find the actual failure point rather than sealing the whole roof line, since a bead of caulk over a lifted flange is a temporary patch at best. Copperfield flashing materials are what we install, bedded into the masonry so the shed line works with gravity. Typical flashing repair runs $400 to $1,200, depending on roof pitch and how much step flashing needs rebuilding.

Lifted and Pulled Counter-Flashing

Counter-flashing should sit in a reglet cut into the brick, not seal against it with caulk alone. When it has pulled out, water goes behind the flashing and into the sheathing. That gets cut back in properly.

Where Leaks Are Often Misdiagnosed

Ceiling stains near a chimney get blamed on flashing when the crown or a masonry joint is the real culprit. Water travels. We test from the top down before quoting a fix.

Chimney Crown Repair

Chimney Crown Repair is the repair or rebuild of the concrete slab at the top of the chimney, which sheds water away from the flue and the masonry below it. A crown with a hairline crack, a missing overhang, or a flue joint that has separated lets water straight down into the chimney’s core. Left alone, that water freezes and spalls the brick from the inside, which turns a crown job into a masonry job. We pour or recast crowns with a proper slope and a drip edge, and we skip the paint-on sealants that crack again by the next spring. Typical crown repair runs $350 to $900, and a full crown rebuild runs higher when the flue tiles need resetting.

Cracks, Slopes, and Overhang

A correct crown slopes away from the flue and overhangs the brick enough to keep water off the chase. Many original crowns do neither, which is why they fail early. We rebuild to that standard rather than skimming over it.

Sealants Versus Rebuilds

A flexible crown coating can buy time on a crown that’s still structurally sound. It can’t fix one that’s cracked through or separated from the flue. We’ll tell you which situation you’re in.

Chimney Repair Companies

Chimney Repair Companies work at very different levels, which is the practical problem when you’re choosing one in Everett. Some are sweep outfits that hand off real repair work; some are roofing or general contractors with a chimney line on the side. We’re a full-service chimney specialist, and sweep, inspection, and repair all stay with the same team, so nothing gets lost in a hand-off. Our technicians have up to 15 years of experience, and we name the brands we use, HeatShield, DuraFlex, Copperfield, Olympia Chimney, Famco, because materials behind a repair matter as much as labor. Repair pricing is set per job by the written estimate, and the estimate itself is free.

Want to talk it through?Free estimate, price agreed before work starts
Call (888) 545-1163

What to Ask Any Chimney Contractor

Ask what brands they install and why, whether they scope the flue with a camera, and whether the inspection report includes photos. Vague answers on any of those are a reason to keep looking. Ask what they won’t do, too.

Mason applying mortar to repair a cracked brick chimney crown in Everett, WA

Red Flags in a Chimney Quote

Any quote that recommends thousands of dollars in work with no photographic evidence is one to question. So is a liner size picked without knowing the appliance. Our reports show you what we saw.

Chimney Masonry Repair

Chimney Masonry Repair is the rebuilding or repointing of the brickwork, mortar joints, and shoulders of the chimney where water and freeze-thaw have taken their toll. Missing mortar, spalled faces, and a loose shoulder near the roofline all allow water deeper into the structure, and Everett’s wet winters cycle that moisture through freeze and thaw at the top of the chase. We repoint to depth rather than smearing a skin of mortar over the joints, and where brick has failed outright we rebuild that section to match the original. Repointing typically runs $600 to $2,500 depending on the amount of joint work, and partial rebuilds run higher. Structural repairs at this level aren’t a handyman line item.

Repointing Versus Rebuilding

Sound brick with failing joints gets repointed. Brick whose face has spalled, or a section that has pulled away from the body of the chimney, gets rebuilt. The two are priced very differently, which is why the site inspection comes first.

Water, Freeze-Thaw, and the Shoulder

The chimney shoulder just above the roofline catches the most weather and fails first. Firm joints and a sound crown keep water off that shoulder. Neglect the crown and the masonry pays for it.

Brands We Service

We work with Olympia Chimney, and we know their cap and component lines well enough to fit them correctly on an existing flue rather than forcing a stock size to work. HeatShield is the product behind much of our structural liner restoration work, and it’s the right call when the original flue is worth saving from the inside. We use HeatShield where a full reline isn’t yet needed, and we tell you plainly when it is.

DuraFlex liner systems carry our full reline work, sized to the appliance and installed as a continuous flue rather than pieced together. Copperfield and Famco cover our flashing and cap installations, where the material has to survive our wet winters without rusting out. Whether you have Olympia Chimney components, Copperfield flashing, or any other make, we can help.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
Need a price for your chimney cleaning?Free estimate, price agreed before work starts
Call (888) 545-1163

Signs You Need a Pro Right Now

  • Water stains or rusty streaks on the chase or ceiling: Water is getting past the flashing, crown, or a masonry joint and traveling inside the structure. Left to freeze and thaw, it costs far more to fix later.
  • Crumbling mortar or spalled brick: When joints crumble at a fingertip, the chase is losing its weather skin. Repointing in time is far cheaper than a rebuild.
  • A white, powdery bloom on the brick: Efflorescence means water is moving through the masonry and drying out through the face. It’s a sign of a water problem, not a cosmetic one.
  • Smoke rolling back into the room: A blocked, undersized, or collapsed liner can’t carry exhaust up and out. That’s a draft and liner problem, and it doesn’t fix itself.
  • Debris or an animal in the firebox: A missing or broken cap lets birds and squirrels in, and their nesting material sits right where flue heat lands. That’s a fire-risk problem and a cap problem at once.

Our Process, Step by Step

  1. 1
    Booked visit and initial walkthrough. We start at the firebox and work up, checking draft, visible liner condition, and the damper before anything goes on the roof. The sweep and inspection come first because you can’t diagnose a chimney you haven’t cleaned.
  2. 2
    Video camera scoping of the flue. We run a camera the length of the flue and record it. Cracks, gaps in the tile joints, and spalling that no one can see from the ground show up here, and you get to watch the footage.
  3. 3
    Exterior and rooftop assessment. Crown, cap, flashing, and masonry joints get checked from the roof and the ground. Water problems are usually found at these four points, not inside the house.
  4. 4
    Written estimate with the evidence attached. You get a per-job written price tied to the specific findings, with the photos that support it. If something can safely wait a season, we say so.
  5. 5
    Repair, then a final check. The repair itself uses the named professional-grade materials, and we verify the fix afterward. That includes a draft check on liner work and a water test where flashing or crown repair was done.

How Much Does Chimney Repair Cost in Everett?

Most chimney repair in Everett falls somewhere between a few hundred dollars for a single component fix and several thousand for a full reline or masonry rebuild. The ranges below are typical for the work we do here:

  • Cap installation or replacement: $150 to $400
  • Crown repair: $350 to $900
  • Flashing repair: $400 to $1,200
  • Masonry repointing: $600 to $2,500
  • Full liner installation: $2,500 to $6,000

Those ranges move with height, access, roof pitch, and how much of the assembly has failed. A two-story chimney costs more to reach than a single-story one, and a steep roof adds labor. A reline on a tall flue with an insulation wrap sits at the top of its range; a short run with clean access sits lower.

How to avoid overpaying: get the finding in writing with photos. Any repair that isn’t backed by camera evidence or an on-roof photo is one to question before you sign it. Our written estimate sets the final price, and it’s free. Nothing is recommended without camera evidence you can see for yourself, and we tell you when work can safely wait.

Questions about your chimney cleaning?Free estimate, price agreed before work starts
Call (888) 545-1163

Our Service Area Near Everett

We cover Everett and the surrounding communities, including Fobes Hill, Bunk Foss, Cathcart, Meadowdale, Clearview, Lake Cassidy, Three Lakes, Lochsloy, Sisco Heights, High Bridge, and Esperance. Booked visits in the closer neighborhoods are the easiest to fit into the day, and we route farther jobs into the schedule so no one’s waiting on a call-back. If you’re in chimney repair territory out toward Fobes Hill, or closer in around chimney repair work in Bunk Foss, we’ll give you a realistic window when you book. Call (888) 545-1163 to get on the schedule.

Serving Everett, WA – Our Local Coverage Area

We serve Everett and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions About Chimney Repair in Everett

Schedule Your Chimney Repair Service in Everett Today

If your chimney has a crack you can see, a leak you can’t trace, or a liner that may be past its life, book a visit and let us find the actual problem before you spend on a fix. Estimates are free, and the written estimate sets the final price. Call (888) 545-1163. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.

Written by the team at Chimney Sweep Everett.

Why Everett Chooses Chimney Sweep Everett

We set the standard for chimney repair in Everett.

Evidence Before Recommendations

Every sweep includes a camera inspection and a photo report. If we find something, you see it before we quote it - no repair is ever recommended on our word alone.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Everett

Getting your chimney repair project started is simple.

1

Call or Request a Free Estimate

Tell us about your chimney repair project and we set up a free visit. No obligation and no hidden fees.

2

Licensed Estimator Visits

A licensed, insured estimator inspects and measures on site, then gives you a clear written price.

3

Scheduled and Done Right

Your crew does the work on the date in your quote, backed by our workmanship warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local chimney repair pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
  4. 4
    You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.

What Everett Customers Say

Trusted by homeowners across Everett and surrounding areas.

★★★★★

"Swept it, capped it, and installed a proper damper. The downdraft smell in the summer that we'd lived with for years is gone."

Brooke Padgett
★★★★★

"Drop cloths everywhere, HEPA vac, and not a speck of soot on the carpet. I'd been dreading the mess for nothing."

Wade Rhodes
★★★★★

"Fireplace had never drawn properly since we moved in. He found the damper was only opening halfway due to a bent linkage and fixed it in ten minutes."

Heather Quinn

Ready for Chimney Repair in Everett?

Call now for a free estimate, or request one below. Licensed, insured, and ready to schedule your free estimate in Everett.

(888) 545-1163

Request a Free Estimate in Everett

Tell us about your chimney repair needs. We'll get back to you to set up your free estimate.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Local Service Coverage
Call Now - We Answer 24/7