Chimney Liner & Rebuild Cost in Everett - You See the Footage Before You Get a Price

Liner and masonry work is where this trade gets a bad name, so nothing is quoted until you have seen the camera footage yourself. Then a written, itemized price with no scope creep.

✓ Licensed & Insured ✓ Written quotes ✓ Free estimates
Call (888) 545-1163

Call to schedule your free estimate

Work is performed by our local vetted partner.

🛡 Licensed & Insured 📝 Written Estimates 💲 Upfront Pricing · Free Estimates
Sweep & inspectionSweep & inspection
Caps & crownsCaps & crowns
Flue reliningFlue relining
Masonry repairMasonry repair
Gas fireplace serviceGas fireplace service
Every visit starts with

Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed

Worth knowing

Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.

Get your free estimate
Explore

Styles & brands we work with

  • Sweep & inspection
  • Caps & crowns
  • Flue relining
  • Masonry repair
  • Gas fireplace service
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
Questions about your chimney cleaning?Free estimate, price agreed before work starts
Call (888) 545-1163

How Much Does Chimney Liner & Rebuild Cost in Everett?

Chimney liner and rebuild work in Everett typically runs $2,400 to $8,500 for a full stainless liner installation, and $3,800 to $22,000 when the job includes masonry rebuilding above the roofline. A straightforward liner replacement on a single-story home usually lands closer to $2,400-$4,200, while a full chimney rebuild after years of Pacific Northwest weather exposure sits at the higher end.

The spread is wide because liner and rebuild are two different trades on the same structure. Lining solves the inside; rebuilding solves the outside. Many Everett homes need some of both, and knowing which part of your chimney is failing is the difference between a $2,800 liner job and a $14,000 rebuild you didn’t actually need.

Key Takeaways

  • Stainless liner installation in Everett: typically $2,400-$8,500
  • Partial or full masonry rebuild: typically $3,800-$22,000
  • HeatShield liner restoration (when the existing flue is sound): often under $3,000
  • Free estimates, upfront written pricing, and one team handling sweep, inspection, and repair

Call (888) 545-1163 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.

Chimney Liner & Rebuild Cost Breakdown (2026)

Here’s how the numbers break down for an Everett home in 2026. Every job is priced per job by the written estimate, but these ranges give you a realistic starting point before you call.

Line Item Typical 2026 Range (Everett)
Chimney inspection (Level 1 or Level 2) $150-$450
Standard chimney sweep $180-$350
Stainless steel liner, single-flue install (DuraFlex) $2,400-$5,200
Multi-flue or large-diameter liner system $4,800-$8,500
HeatShield liner restoration (existing flue salvageable) $1,800-$3,400
Partial masonry rebuild (crown, top courses, or upper stack) $3,800-$9,500
Full masonry rebuild above roofline $12,000-$22,000
Crown rebuild or replacement $600-$1,800
Chimney cap and top-sealing damper $350-$900
Exterior waterproofing (Gelco or Famco systems) $500-$1,600
Flue tile crack repair (HeatShield joint repair) $1,200-$2,800

Several things push these numbers up or down. A clay flue that’s still intact but has cracked joints can often be restored with HeatShield rather than torn out and relined with DuraFlex, which saves thousands. A flue that’s collapsed, misaligned, or too small for the appliance can’t be restored, and a full liner install is the right path. On the rebuild side, the big cost drivers are how much masonry sits above the roofline, whether the chimney is freestanding or shares a wall with the house, and how much of the old brick has spalled after absorbing water. Copperfield and Olympia Chimney components are used on the accessory side (caps, dampers, top plates) because they hold up to wet weather better than generic hardware.

An important distinction: a rebuild is not the same as a reline. Rebuilding fixes the brick and mortar shell. Relining fixes the flue inside it. Most Everett chimneys that have gone two or three decades without waterproofing need one or the other, and sometimes both. A proper inspection tells you which, and that’s what keeps you from paying for work your chimney doesn’t need.

Want to talk it through?Free estimate, price agreed before work starts
Call (888) 545-1163

What Affects Chimney Liner & Rebuild Pricing in Everett

  • How much rain the chimney has absorbed. Everett’s wet winters are hard on masonry. Brick that soaks up water, freezes, and spalls has to be cut out and replaced, and that labor adds up fast. Chimneys without a proper cap or waterproofing fail sooner than ones that have been protected with Gelco or a Famco system.
  • Flue size and appliance type. A standard wood-burning fireplace flue takes a smaller, less expensive liner than a large masonry heater, a wood insert, or a gas appliance that needs a specific diameter for proper draft. The liner has to match the appliance, not just the flue.
  • Whether the flue can be saved. HeatShield liner restoration works when the original clay tile is structurally sound but has cracked joints and gaps. If the tile is broken out or missing, only a new DuraFlex stainless liner will do, and that’s a different budget.
  • Roofline height and pitch. A steep roof or a tall chimney means more scaffolding, more safety rigging, and more labor hours. Rebuilding a chimney on a two-story Everett home with a steep pitch costs more than the same rebuild on a low-slope ranch.
  • Chimney location. An interior chimney that runs up through the house is easier to access and rebuild than an exterior chimney mounted on the outside wall, which takes the full brunt of weather and often needs more brick replacement.
  • Code and safety corrections. A liner install often reveals a missing cap, a failed damper, or an unlined flue section. Some of these are required fixes for a safe, code-compliant system and get folded into the estimate. Your city’s building department can tell you what permits apply before work begins.

We name the brands we use because the materials behind a repair matter as much as the labor. DuraFlex liners, HeatShield restoration, and Copperfield and Olympia Chimney accessories are what hold up in western Washington weather. Off-brand liners and generic caps tend to fail years earlier, which means paying twice.

Liner Replacement vs. Chimney Rebuild: Which Do You Actually Need?

This is the question that saves homeowners the most money, so it’s worth spelling out. A liner replacement addresses the inside of the chimney: the flue that carries smoke and gases out of the house. A rebuild addresses the outside shell: the brick, mortar, crown, and joints that hold the chimney together and keep water out.

If your inspection flagged a cracked flue, a draft problem, or deteriorated tile, and the brickwork above the roofline looks solid, you likely need a liner and nothing more. If the crown is crumbling, the mortar joints are washing out, or the top of the chimney is leaning, that’s structural and needs a rebuild. Many Everett homeowners get told they need a full rebuild when the real problem is a failed crown and a poorly sealed cap, both of which cost far less to fix.

One team handling your sweep, inspection, and repair means the diagnosis and the fix come from the same people. No hand-off gap between a sweeper who points out a problem and a mason who shows up weeks later with a different opinion. We diagnose the full picture, inside and out, before we price anything.

If you’re not sure where your chimney stands, start with a chimney sweep everett and inspection. That gives us the information to tell you whether you’re looking at a liner job, a rebuild, or neither.

Need a price for your chimney cleaning?Free estimate, price agreed before work starts
Call (888) 545-1163

How Much Does Chimney Liner Installation Cost in Everett?

A stainless steel chimney liner installation in Everett typically costs $2,400 to $5,200 for a standard single-flue home, and $4,800 to $8,500 for larger or multi-flue systems. The liner itself is a fixed, insulated stainless tube sized to your appliance. The labor is what varies, driven by roof access, flue height, and how much prep work the old flue needs.

DuraFlex liner systems are what we install because they’re rated for the fuel types and temperatures a real chimney sees, and they come in the diameters needed to match wood, gas, or oil appliances. A liner that’s undersized for the appliance causes draft problems that no amount of cleaning will fix.

If the flue is structurally sound but leaking at the joints, HeatShield restoration can rebuild the liner surface from the inside at a lower cost, often under $3,000. That’s a structural repair, not a surface fix, and it’s a meaningfully different service than a sweep. Not every chimney qualifies, and an inspection tells you which route is right.

Call (888) 545-1163 for a free liner estimate. We answer 24/7.

How Much Does a Chimney Rebuild Cost in Everett?

A partial chimney rebuild in Everett typically runs $3,800 to $9,500, and a full masonry rebuild above the roofline runs $12,000 to $22,000. Partial means we’re replacing the crown, the top few courses, or the upper stack that takes the worst weather. Full means the entire above-roof section comes down and gets rebuilt.

Everett’s combination of wind-driven rain and occasional hard freezes is the main reason masonry fails here. Water gets into the brick, freezes, expands, and pops the face off the brick. Once that starts, patching mortar over spalled brick doesn’t last. The rebuild also includes a properly sloped crown and a sealed cap, which is what protects the chimney going forward. A rebuild without waterproofing just resets the clock.

We finish rebuilds with Gelco or Famco exterior protection so the new masonry sheds water the way it should. Rebuilding is heavy, detail-driven work, and it’s the part of chimney care where using a dedicated specialist instead of a general handyman makes the biggest difference.

Call (888) 545-1163 for a free rebuild estimate. We answer 24/7.

How to Save on Chimney Liner & Rebuild in Everett

  • Get an inspection before you get a repair quote. An inspection tells you exactly what’s failing and what isn’t. It’s the cheapest way to avoid paying for a rebuild when a liner and a new crown will do.
  • Catch water damage early. A $500-$1,600 waterproofing job on a sound chimney prevents the kind of brick spalling that leads to a $15,000 rebuild a few winters later.
  • Restore instead of replace when the flue is sound. HeatShield liner restoration costs less than a full reline and is the right call when the tile is intact but the joints have opened up.
  • Bundle the sweep and inspection. Having the chimney swept and inspected in one visit means one diagnostic pass and one accurate quote for any repair that follows.
  • Ask what’s actually required versus recommended. A good estimate separates the safety-required items from the nice-to-haves so you can prioritize. Your written estimate sets the final price, and it should be in writing before any work starts.
  • Protect the new work with a proper cap and damper. A chimney cap and top-sealing damper keep water and animals out, which extends the life of both a new liner and new masonry.

Estimates are free, and they’re the best way to find out where your chimney actually stands. Call (888) 545-1163 to schedule one. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.

Questions about your chimney cleaning?Free estimate, price agreed before work starts
Call (888) 545-1163

FAQs – Chimney Liner & Rebuild Cost

How much does chimney liner installation cost in Everett?

Chimney liner installation in Everett typically costs $2,400 to $5,200 for a standard single-flue home and up to $8,500 for larger or multi-flue systems. The price depends on flue height, roof access, and whether the old flue needs prep work first. Call (888) 545-1163 for an exact quote. Estimates are free.

How much does a chimney rebuild cost in Everett?

A chimney rebuild in Everett typically costs $3,800 to $9,500 for a partial rebuild and $12,000 to $22,000 for a full masonry rebuild above the roofline. The range depends on how much brick has to be replaced, roofline height and pitch, and whether the chimney is interior or exterior. Call (888) 545-1163 for a free estimate.

Is it cheaper to repair or replace a chimney liner?

Repairing a liner with HeatShield restoration is usually cheaper than a full replacement, often under $3,000 versus $2,400 to $5,200 for a new stainless liner. Restoration only works when the original clay tile is structurally sound with no missing sections. A full DuraFlex liner install is the right call when the tile is broken out or too far gone. Call (888) 545-1163 to find out which applies to your chimney.

How much does chimney waterproofing cost in Everett?

Chimney waterproofing in Everett typically costs $500 to $1,600, depending on the size and condition of the masonry. Gelco and Famco systems are what we use because they let the masonry breathe while keeping rain out. It’s the cheapest way to protect the investment a liner or rebuild represents. Call (888) 545-1163 for a free estimate.

Can you come today?

Same-day service is often available. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Call (888) 545-1163 and we’ll get you on the schedule and out to look at your chimney. Estimates are free.

Why a Dedicated Chimney Specialist Matters on Everett Liner and Rebuild Work

Chimney work is a safety trade. We treat it like one.

Liner and rebuild projects touch every part of a chimney system: the flue, the crown, the cap, the masonry, the waterproofing. A general handyman can patch a crown. A roofer can flash around a chimney. But neither typically has the liner sizing knowledge, the restoration tools, or the materials to solve the underlying problem. That’s why we handle sweeping, inspection, and repair under one roof, so the diagnosis and the fix come from the same team. Our technicians have up to 15 years of experience across the full range of chimney systems.

We also use professional-grade products on every job: DuraFlex liner systems, HeatShield restoration, Copperfield and Olympia Chimney components, and Gelco and Famco weatherproofing. These are the brands other chimney specialists trust because they’re engineered for the fuel types and weather conditions that chimneys actually face.

If you’ve had an inspection flag or your insurer is asking for documentation on your chimney’s condition, we can work with you on the inspection report and the repair scope. And we keep our focus narrow on purpose. Chimneys are all we do, not a side service tacked onto a general contracting list. That focus shows up in the quality of the diagnosis and the long-term durability of the work.

Contact Us for a Free Chimney Liner & Rebuild Estimate

The fastest way to know what your Everett chimney needs and what it will cost is to have someone who works on chimneys every day take a look. We give you a written estimate before any work begins, and the estimate is free. If you’re in the Everett area and your chimney is drafting poorly, leaking, or showing signs of masonry damage, don’t wait for the next round of storms to make it worse.

Call (888) 545-1163. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’ll inspect the full system, explain what’s actually failing and what isn’t, and give you a straight price for the liner, the rebuild, or both.

Pricing reflects the Everett market as of 2026. Chimney Sweep Everett offers free estimates – call (888) 545-1163.

Written by the team at Chimney Sweep Everett.

What Our Customers Say

★★★★★ 4.9 from 9+ reviews

"Swept it, capped it, and installed a proper damper. The downdraft smell in the summer that we'd lived with for years is gone."

- Brooke Padgett

"Drop cloths everywhere, HEPA vac, and not a speck of soot on the carpet. I'd been dreading the mess for nothing."

- Wade Rhodes

"Fireplace had never drawn properly since we moved in. He found the damper was only opening halfway due to a bent linkage and fixed it in ten minutes."

- Heather Quinn
Need Chimney Cleaning help in Everett? Licensed & insured · free written estimates
Call (888) 545-1163

Request a Free Estimate

Tell us what's going on in Everett. We'll get back to you fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - We Answer 24/7
Local Service Coverage
Call Now - We Answer 24/7