Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Everett Homeowners Choose DuraFlex Chimney Cleaning
We provide independent DuraFlex chimney cleaning and service in Everett, WA. DuraFlex is a flexible stainless steel chimney liner, and we clean, inspect, repair and reline DuraFlex systems across the city while working around the liner’s real weak points: the top-plate seal, the corrugations, and the appliance end.
Chimney Sweep Everett is an independent service provider. We’re not affiliated with, authorized by or a dealer for DuraFlex, and we don’t sell the brand. What we do is service it. Our technicians have up to 15 years of experience with flexible stainless liners, and we handle the full job – sweep, Level 2 inspection, creosote removal, cap replacement – so you’re not coordinating three contractors on one flue. Call (888) 545-1163 for a free estimate.
Why Trust Chimney Sweep Everett for Your DuraFlex Chimney Cleaning?
Flexible stainless liners are not all the same to work on. The corrugations that let a DuraFlex liner flex down an offset masonry flue are also where soot and creosote collect, and the top termination is where water gets in. Our technicians know both ends of that liner because we see them every week: the cap and crown interface at the top, the appliance connector at the bottom, and the long run in between.
We use quality parts that fit DuraFlex equipment – compatible termination plates, caps and connector hardware – and we fit them the way the liner was designed to be terminated, so the assembly stays sealed. We work warranty-safe: we don’t cut, crush or re-wrap a liner to make it fit, and we don’t substitute a part that changes how the system was built. If a prior install has a problem we can’t work around, we say so before we touch it.
Because we’re independent, our advice is based on the condition we find in your Everett flue, not on a manufacturer program. If the liner tests sound, we clean and reseal. If it doesn’t, we tell you why. That’s the whole approach.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common DuraFlex Chimney Cleaning Problems We Fix in Everett
Flexible stainless liners fail in predictable places. These are the ones we deal with most in Everett:
- Liner-to-cap terminations loosening or corroding. This is the most common one. Where the flexible liner meets the top plate at the crown, the connection can loosen over seasons or corrode in wet marine air. Once it does, water tracks down the outside of the liner, dampens the creosote and shows up as a smoky smell in the house after rain.
- Creosote and soot packing in the corrugations. Wood stoves run at a low, smoldering burn – which is how a lot of Everett homes heat during long wet stretches – lay down creosote that fills the liner’s corrugations instead of flaking off. Packed corrugations cut draft and raise fire risk, and they need proper creosote removal, not a quick brush.
- Insulated wrap degrading or tearing. Insulated liner wrap protects clearances and holds heat for draft. It also tears easily during a careless install, and a torn or degraded wrap quietly undercuts both jobs. We check the wrap as part of a Level 2 inspection.
- Rust-through or pitting at the bottom section. The lowest stretch of liner, right above the appliance connector, often sits where a damper or firebox transition was cut. That’s the wettest, most acidic part of the flue, and it’s where pitting and rust-through usually start.
- Wrong or missing cap on the termination. A cap that doesn’t match the termination lets rain straight into the flue. We replace it with one that fits the system and seals against the top plate.
Four of those five are clean-and-reseal jobs. One of them – packed or compromised corrugations – is a reline conversation. The inspection is what tells you which one you’re in.
DuraFlex Parts & Our Repair-vs-Replace Approach
We use DuraFlex-compatible OEM termination plates, caps and connector hardware wherever they’re still available. Where OEM isn’t obtainable, we use quality aftermarket stainless fittings that match the system. We don’t claim to stock genuine DuraFlex parts, and we won’t tell you a part is OEM when it isn’t.
On repair versus replace, the rule is simple. If a single section is damaged and the rest of the liner tests sound, we recommend targeted replacement. Full reline only comes up when the corrugations are packed solid or the wall thickness is compromised. A resealed termination and a clean flue is a much smaller job than a reline, and we’ll say so when that’s what your Everett chimney actually needs. Call (888) 545-1163 and we’ll walk you through what we find.
Our DuraFlex Service Process – Step by Step
- 1
Diagnosis. We start with a Level 2 inspection – camera up the flue, top termination pulled and checked, appliance end examined. We document the liner condition at both ends, because a top-plate leak and a bottom-section pit are two different jobs.
- 2
Cleaning or repair. Creosote removal comes first: the liner gets swept so we can see the steel underneath. Then the repair – resealing the termination, replacing a corroded cap or top plate, or swapping a damaged section. If the liner needs a reline, we explain why before anyone quotes it.
- 3
Test. We check draft and confirm the termination seals before we call it done. A resealed top plate that still pulls water isn’t finished.
- 4
Warranty-safe handoff. We leave you with the record of what was found, what was replaced and what condition the liner is in – the documentation you need if a warranty question ever comes up.
See the difference
Before
After
Before
After
Before
AfterDuraFlex Products We Service & Install in Everett
We service and install DuraFlex stainless flexible chimney liner systems, single-wall and insulated, along with the supporting components that make the system work: rigid stainless liner sections for straight runs, appliance connectors, liner-to-cap termination kits, and ovalized flexible liner for tight masonry flues. We handle cap replacement as part of the termination work. We don’t manufacture or sell DuraFlex, and we don’t claim to stock it – we service what’s in your chimney.
We Also Service These Brands
DuraFlex is one liner system in a much broader toolkit. We also work with HeatShield for structural liner restoration and Gelco for weatherproofing and exterior chimney protection, plus Olympia Chimney, Famco and Copperfield for other repair and installation work. If your Everett chimney has a mix of brands in it – a HeatShield-relined flue with a DuraFlex appliance connection, say – we can service the whole assembly rather than handing part of it off.
FAQs – DuraFlex Chimney Cleaning Service in Everett
No. Chimney Sweep Everett is an independent service provider. We’re not affiliated with, authorized by, certified by or a dealer for DuraFlex, and we don’t sell the brand. We service DuraFlex liner systems and their supporting components as an independent shop, which means our recommendations come from the condition of your flue, not from a manufacturer program.
Yes. A DuraFlex flexible stainless liner can be swept, and it needs to be. The flexible liner’s corrugations are where soot and creosote pack in, especially when a wood stove has been run at a low burn through Everett’s wet season. We use the right tools for a stainless liner so we don’t damage the steel or the wrap, then follow the sweep with a Level 2 inspection to check the termination and the appliance end.
A smoky smell after rain almost always means water is getting in at the top termination. The most common cause is the liner-to-top-plate connection loosening or corroding, so rain tracks down the outside of the flexible liner and dampens the creosote inside. The fix is usually a resealed termination and a cap replacement, not a new liner. We pull the cap and top plate, clean the flue and liner, reseal the termination and document the liner condition from both ends.
The inspection tells you. If the corrugations are packed with creosote but the steel is sound, it’s a cleaning plus a reseal – that’s the majority of what we find in Everett. If the corrugations are packed solid or the wall thickness is compromised at the bottom section, that’s a reline conversation. We test the rest of the liner before recommending a full replacement, and we’ll tell you plainly when a targeted repair is enough.
Yes. The cap has to match the termination so it seals against the top plate – a mismatched or missing cap lets rain straight into the flue and is one of the most common causes of water intrusion in Everett chimneys. We use DuraFlex-compatible OEM termination plates and caps wherever they’re still available, and quality aftermarket stainless fittings where OEM isn’t obtainable.
Often, yes. Where a single section is damaged but the rest of the liner tests sound, we recommend targeted replacement – swapping that section rather than the whole run. A full reline only comes up when the corrugations are packed or the wall thickness is compromised. Our technicians have up to 15 years of experience with flexible stainless liners and use quality parts that fit DuraFlex equipment.
We service and install DuraFlex stainless flexible chimney liner systems – single-wall and insulated – plus rigid stainless liner sections for straight runs, appliance connectors, liner-to-cap termination kits and ovalized flexible liner for tight masonry flues. We don’t manufacture or sell DuraFlex, and we don’t claim to stock it.
A chimney sweep with a Level 2 inspection on a DuraFlex-lined flue is quoted per job, and the written estimate sets the final price. Resealing a top termination and replacing a cap costs more than a sweep alone; a reline costs considerably more. Nothing is recommended without camera evidence you can see for yourself, and we’ll tell you what can safely wait. Call (888) 545-1163 for an exact quote – estimates are free.
Book Your DuraFlex Service in Everett, WA
Whether your DuraFlex liner needs a sweep, a resealed termination or a full reline assessment, we’ll look at both ends of it and tell you what the steel actually shows. Call (888) 545-1163. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Estimates are free and the written quote sets the price.
Written by the team at Chimney Sweep Everett.